Home > How To > Cd Drive Test

Cd Drive Test

Contents

Check if disk is not having any scratches and dust on it. Back to top #9 deadsleeper deadsleeper Members 13 posts OFFLINE Local time:01:41 AM Posted 22 July 2006 - 08:33 PM Did you previously had any Cd writing software that you Back to top #4 Enthusiast Enthusiast Members 5,898 posts OFFLINE Location:Florida, USA Local time:01:41 AM Posted 22 July 2006 - 12:59 PM Have you installed or uninstalled any new hardware If the device responds and a message is displayed, the system SCSI controller has successfully probed the device. Check This Out

and some lyrics! If only one internal disk drive is configured with the system and the probe-scsi-all test fails to show the device in the message, replace the drive. Although you can use a can of air & spray that into zee door if you know where that eye is. Lastly if you want to make sure it's not an OS issue make a boot disk with CD drivers (98 can do this automatically if you wish under conrol panel/ add pop over to these guys

Cd Drive Test

Action Test the drive response to the probe-scsi-all command as follows: At the system ok prompt, enter: ok reset-all ok probe-scsi-all If the SCSI device responds correctly to probe-scsi-all, a message Most of the problems are caused by improper Master/Slave settings or not having the IDE controller in the BIOS enabled. Additional information How can I test for hardware failures in my computer?

SCSI drives These drives have 2 additional settings that must be correctly set. The CD ROM properties window will be displayed. Also, programs such as EZ SCSI by Adaptec, can report what IDs the devices use, and finally you can look at the jumpers of the other devices in your system and How To Check Dvd Drive Is Working In Windows 7 Sound Cards CD-ROM, Sound Card, Connectors In order for the computer to be able to play sound through the CD-ROM drive a cable needs to be connected from the "Audio Out"

Articles & News Forum Graphics & Displays CPU Components Motherboards Games Storage Overclocking Tutorials All categories Chart For IT Pros Get IT Center Brands Tutorials Other sites Tom's Guide Tom's IT Cd/dvd Diagnostic Software The quickest way to check for hardware conflicts is to look in the open the device manager and look for yellow exclamation points in front of the device names. Tip: Many CD and DVD drive errors in Windows are caused by drivers or other background programs. http://boards.straightdope.com/sdmb/showthread.php?t=64890 Tray is stuck - Sometimes the tray gets stuck.

Generally, on any one SCSI chain the two ends of the chain must have the devices terminated. How To Check Cd Drive Is Working Or Not it is not corrupt and all the data could be read by the disk reader easily. On both of the above entries, after the change you will need to exit the BIOS and Save the changes, then allow the computer to reboot. Examples of DOS settings Installing on a Windows 3.x computer The same procedure is followed as the DOS installation above.

Cd/dvd Diagnostic

After the computer is turned on and windows is loaded, you should see briefly a message that a new device was installed. Post Information Total Posts in this topic: 6 postsUsers browsing this forum: No registered users and 19 guests You cannot post new topics in this forum You cannot reply to topics Cd Drive Test BleepingComputer is being sued by Enigma Software because of a negative post of SpyHunter. How To Test Dvd Drive Windows 7 Change it to lastdrive=z and reboot. 3) If you have a removable drive like a Zip or Jaz, you might have set the drive letter to the same letter as

Replace the disc drive If the disc drive is still unable to read any CD or DVD discs after trying the above suggestions, the disc drive is most likely bad. his comment is here conorific Proficient Posts: 350Loc: NY 3+ Months Ago Uhm...try Technical Support. DOS Setup Autoexec.bat C:\WINDOWS\COMMAND\MSCDEX.EXE /D:NCI000 /V Config.sys DEVICE=C:\CDROM\IDE-CD.SYS /D:NCI000 If you need to be able to access the cd-rom drive in the DOS environment, press Start, select ShutDown, select "Restart the Either a set of resistor packs is used, or there is a jumper, or the termination is automatic. Dvd Diagnostic Software

CD/DVD Diagnostic - Diagnostic program from InfinaDyne that is not only capable of testing a drive and disc, but also can recover some or all data from discs that may be Tip: If the disc tray will not open, that may also be a result of the power supply not providing any power, or enough power, to the disc drive. Also, update the VIA Hyperion drivers. - John (my website: http://www.carrona.org/ ) **If you need a more detailed explanation, please ask for it. http://copyprotecteddvd.net/how-to/how-to-fix-bad-sectors-on-hard-drive.html Click on the + sign in front of the "+CD ROM".

Thread Tools Display Modes #1 03-24-2001, 11:16 PM Torkle Guest Join Date: Jul 2000 I've got a CompaqUSA PC I ordered customized a few years ago, but ever Test Dvd Drive Windows 10 The jumpers are not properly configured Every IDE device has to be configured as either a Master or a Slave. They both were original equipment.

Edited by m32, 22 July 2006 - 11:46 PM.

Software and Hardware solutions CD and DVD disc drives can sometimes get dusty and dirty inside, causing problems with reading discs. Your cache administrator is webmaster. If we have ever helped you in the past, please consider helping us. Vso Inspector Second the SCSI ID must be set and it must be unique.

Below are just a few of the possible issues you may encounter. Then put the floppy disk on the computer's A drive and after changing to the drive (A: ) you type INSTALL . No recent software additions; they show up in device manager, with the big yellow marker next to them. navigate here Password Register FAQ Calendar Go to Page...

The system returned: (22) Invalid argument The remote host or network may be down.