Home > Hard Drive > Master Slave Hard Drive Setup

Master Slave Hard Drive Setup

Contents

EDIT Edit this Article Home » Categories » Computers and Electronics » Hardware » Internal Components ArticleEditDiscuss Edit ArticleHow to Configure Master and Slave in BIOS for Two Hard Drive Disk I would purchase a USB memory device now If your 98 PC has USB. Ekle Bu videoyu daha sonra tekrar izlemek mi istiyorsunuz? BUY NOW FREE TRIAL BACKUP & RESTORE For Business » Todo Backup WorkstationBuyTry Todo Backup ServerBuyTry Todo Backup Advanced ServerBuyTry For Home & Home Office » Todo Backup FreeDownload Todo Backup this contact form

That means no jumpers to set and no fear of getting it wrong. Flag Permalink This was helpful (0) Collapse - Re: Install old hard drive as slave drive? Help answer questions Learn more 134 MESSAGES LOG IN Log in Facebook Google Email No account yet? The figure below depicts the jumper settings for the U-Series and Barracuda ATA drive families (most Seagate ATA drives above 20 GBytes).

Master Slave Hard Drive Setup

Flag Permalink This was helpful (0) Collapse - Thanks, Berfert by grandpaw7 / August 27, 2004 12:35 AM PDT In reply to: Re: Many thanks to Kee, remusson and rhbass I Needle-nose pliers for removing or adding jumpers. by R. However, for performance reasons they are sometimes put on the secondary channel, and often the system assemblers don't bother to change the jumpers.

They should have some instructions posted. This was different from the normal IDE cables at the time. About this wikiHow How helpful is this? How To Install A Second Sata Hard Drive In Windows 7 This pin always goes on the same side as the power connector.

Press the "Enter" key to detect and configure the primary hard disk, making it the Master Drive. 5 Move the cursor to the "Primary Slave" selection and press "Enter" again. If you have an older drive please visit our Technical Library and find your model number for details on jumper configuration. Watch carefully for the initial boot screen to display and tap the necessary key to over-ride the boot process. http://www.pcadvisor.co.uk/how-to/pc-upgrades/how-slave-sata-drive-3461780/ Battery Geek 192.542 görüntüleme 9:18 Hard Drive Not Found Error on boot up by Britec - Süre: 10:01.

Good deal. Sata Hard Drive Slave Jumper Setting BUT just be aware that the First partition of the old disk (C drive of the old disk) will be shown as the D drive in the new computer. However, I don't know enough about Linux file systems to advise whether you can safely get Windows to deal with that HDD. On even older mainboards you'll find a 32 GB limit.

What Is A Slave Hard Drive

Answer this question Flag as... http://www.tomshardware.com/forum/277623-32-master-slave-sata-drives After installing the additional hard-drive, you will need to change your computer's Basic Input Output System (BIOS) settings to "Master/Slave." Steps 1 Restart your computer. Master Slave Hard Drive Setup Wonder what connects to where on the cable? Master Slave Hard Drive Jumper Settings In fact, you actually specify a priority sequence of devices to try to boot from - if one fails to boot, it proceeds to the next in your sequence until it

Product Key Does Not Match Current Windows SKU Error Review of FastAgain PC Booster and How to Uninstall it How to Remove MSBLAST.EXE worm How to Remove Content Advisor Password in http://copyprotecteddvd.net/hard-drive/i-can-39-t-partition-my-hard-drive-mac.html The install disk comes on a floppy so if you don't have one then you'd better be able to do a BIOS update. Can I set my IDE drive as slave if I'm using an IDE to SATA converter? As I did mention in one of my posts, I have foregone the idea of installing the old drive on my new computer for a number of reasons, including the fact How To Slave A Sata Hard Drive

Bu videoyu Daha Sonra İzle oynatma listesine eklemek için oturum açın Ekle Oynatma listeleri yükleniyor... Usually the first BIOS screen to appear is the primary, or basic screen. 4 In the CMOS menu, find "Hard Disk" and then the "Primary Master" selection. To connect the IDE cable to the motherboard you'll have to find something that looks like this: Each connector represents 1 IDE channel. http://copyprotecteddvd.net/hard-drive/hard-drive-failure.html If this is a secondary drive then you're obviously after pure storage space so just make it a primary partition and allocate 100% of your space to it.

Most modern CD drives are ATA33 while the modern hard drives are ATA133. Difference Between Master And Slave Drive BUY NOW FREE TRIAL Data Recovery Wizard for Mac Best Mac data recovery software recovers whatever you lost from Mac machines & storage devices. See more: Install Hard Drive Related Articles - ALSO ON EaseUS SOFTWARE Known Improvements in Windows 10 Version 1607 Anniversary Update. 2016-05-27 15:25:23 Jean - Here are the known improvements in

Yes No Can you tell us more?

most likely 0) LIST PARTITION SELECT PARTITION (followed by your partition number. JUST ENSURE YOU SET YOUR JUMPER TO SLAVE SETTINGS PRIOR TO INSTALLATION. It also offers some basic and advanced features like create, delete, resize/move, format, copy partition for better Windows hard disk management. How To Slave A Hard Drive To Recover Data Note: If you want to recover data from the "OLD" drive, don't do this!

Then I can take it with me if anyone wants to see any photos and just plug it in to their computer (I know it's corny, but hey, it works!) Hope The followed screen looks like this. Who is going to install it? his comment is here ATAPI devices such as optical, Zip and tape drives are jumpered in pretty much the same way as hard disks.

One problem I am having is that I have a low capacity brain, and as I learn new stuff, the old stuff gets pushed out to make room for the new. There are many more performance considerations to take into account when deciding how to jumper your IDE devices, if you are using several different ones on more than one channel. You could then have a directory made called "Old HD" and copy the whole thing into it. It sounds like a good idea to me, but I thought I'd see if there are reasons I may not want to do this.Thanks, grandpaw Discussion is locked Flag Permalink You

You can free download and up… Related Products Data Recovery Software Data Backup Software Partition Manager Software PC Transfer Software Mac System Utility File Sync Utility Top 10 Hot Articles Recover How to Troubleshoot and Solve USB Device Error Code 10 Spooler Subsystem App has encountered a problem and needs to close Error and How to Fix it How to Fix Problem